home *** CD-ROM | disk | FTP | other *** search
/ Tech Arsenal 1 / Tech Arsenal (Arsenal Computer).ISO / tek-17 / et3win31.zip / README.DOC < prev    next >
Text File  |  1992-04-16  |  3KB  |  80 lines

  1.  
  2.  
  3.       ET3000 Windows 3.1 Video Driver Installation Instructions
  4.  
  5. This driver disk is designed to allow you to select or change the
  6. video driver for Windows 3.1 using Windows Setup. Setup can be
  7. executed from within Windows, or from DOS. Note that these driver
  8. files are in Microsoft compressed format and can only be accessed and
  9. executed by installing through Windows Setup. Simply copying the files
  10. into your \Windows\System subdirectory WILL NOT work and may corrupt
  11. your Windows installation. Installing the drivers correctly is,
  12. however, a simple process. It is accomplished by following these
  13. instructions:
  14.  
  15.  
  16. Installation from floppy disk
  17.  
  18. 1) Insert your Driver Disk in the appropriate floppy drive.
  19.  
  20. 2) From your Windows directory, type SETUP and select DISPLAY to
  21. change the video driver. Or, with Windows running, select Setup from
  22. the Program Manager Main group. Refer to your Microsoft Windows User's
  23. Guide for assistance in running Setup from inside Windows.
  24.  
  25. 3) Select "Other disk..." to direct the program to the floppy disk
  26. holding the new drivers. Note that after the drivers are installed,
  27. you will not have to select "Other disk..." again should you decide to
  28. change resolutions. Look for the ET3000-based drivers in the Display
  29. selection menu to select the display resolution you want.
  30.  
  31. 4) When asked where the drivers will be found, state the following:
  32.  
  33.         A:\
  34.  
  35. Following instructions 6-7 below.
  36.  
  37.  
  38. Installation from Hard Disk
  39.  
  40. 1) Having the drivers loaded on the hard disk will make it easier and
  41. faster to change resolutions in the future. Make a subdirectory to
  42. hold the driver files.
  43.  
  44. example: C:>md \et3drv
  45.  
  46.         and switch to that subdirectory (C:>cd \et3drv)
  47.  
  48. 2) Insert the drivers disk into the appropriate drive and type the
  49. following command:
  50.  
  51.         COPY A:\*.*
  52.  
  53. 3) From your Windows directory, type SETUP and select DISPLAY  to
  54. change the video driver. Or, with Windows running, select Setup from
  55. the Program Manager Main group. Refer to your Microsoft Windows User's
  56. Guide for assistance in running Setup from inside Windows.
  57.  
  58. 4) Select "Other disk..." to direct the program to the subdirectory
  59. holding the new drivers. Note that once the drivers are installed, you
  60. should not have to select "Other" again should you decide to change
  61. resolutions. Look for the ET3000-based drivers in the Display
  62. selection menu to select the display resolution you want.
  63.  
  64. 5) When asked where the drivers will be found, state the following
  65. (deleting what the program has displayed in the input window):
  66.  
  67.         [drive:]\[directory]
  68.  
  69.         e.g.: C:>\et3drv
  70.  
  71. 6) A standard Windows selection menu will appear with additional video
  72. drivers from which to select.
  73.  
  74. 7) Proceed normally through the remainder of the process. Check
  75. Microsoft Windows installation procedures if necessary.
  76.  
  77. 8) If you are having problems installing these drivers please contact your 
  78. board vendor for further assistance.(as your vendor may have done proprietary
  79. enhancements that require custom drivers)
  80.